Top 3 pipe radius chart

Long Radius Pipe Bends Dimensions (Pipe U Bends)
For formed Product (WP) Dimension is roofed in
ASME B16.9- that is normal for store-bought formed Butt-welding Fittings for size NPS 1⁄₂ to NPS 48” and
And B16.28- that is normal for formed Steel Butt-Welding Short Radius Elbows and Returns for size NPS 1⁄₂ to NPS 24”




1.    pipe radius chart
PIPE SIZE
OUTedge DIAMETER
BACK side
CENTER
Inch.
OD
A
B
C
D
1/2
21.3
48
76
3/4
26.7
43
57
1
33.4
56
41
76
51
1 1/4
42.2
70
52
95
64
1 1/2
48.3
83
62
114
76
2
60.3
106
81
152
102
2 1/2
73
132
100
191
127
3
88.9
159
121
229
152
3 1/2
101.6
184
140
267
178
4
114.3
210
159
305
203
5
141.3
262
197
381
254
6
168.3
313
237
457
305
8
219.1
414
313
610
406
10
273.1
518
391
762
508
12
323.9
619
467
914
610
14
355.6
711
533
1067
711
16
406.4
813
610
1219
813
18
457.2
914
686
1372
914
20
508
1016
762
1524
1016
22
559
1118
838
1676
1118
24
610
1219
914
1829
1219
All Dimensions are in mm




2.    pipe radius chart
Get your Pipe Bends Dimensions in mm (Long & Short Radius)


Here you get the more information about radius bends chat and specification
PIPE SIZE
FITTINGS
FITTINGS
FITTINGS
TEES and ELBOWS
180 RETURN BENDS
180 RETURN BENDS
180 RETURN BENDS
REDUCER
CAP
NPS
O.D. at Bevel (1), (2)
I.D. at End
(1), (3), (4)
Wall Thickness (3)
Centre-to-End Dimension A,B,C,M
Centre-to-Centre O
Back-to-Face K
Alignment of Ends U
Overall Length H
Overall Length E
3 to 3 ½
0.06
0.06
Not < than 87.5% of thickness
0.06
0.25
0.25
0.03
0.06
0.12
4
0.06
0.06
Not < than 87.5% of thickness
0.06
0.25
0.25
0.03
0.06
0.12
5 to 8
0.09
-0.06
0.06
Not < than 87.5% of thickness
0.06
0.25
0.25
0.03
0.06
0.25
10 to 18
0.16
-0.12
0.12
Not < than 87.5% of thickness
0.09
0.38
0.25
0.06
0.09
0.25
20 to 24
0.25
-0.19
0.19
Not < than 87.5% of thickness
0.09
0.38
0.25
0.06
0.09
0.25
26 to 30
0.25
-0.19
0.19
Not < than 87.5% of thickness
0.12
0.19
0.38
32 to 48
0.25
-0.19
0.19
> than 87.5% of thickness
0.19
0.19
0.38
3. pipe radius chart


PIPE SIZE NPS
TOLERANCES
TOLERANCES
ALL DIMENSIONS ARE GIVEN IN INCHES. AND TOLERANCES

Off Angle Q
Off Plane P
(1) Out-of-round is that the add of absolute values of and and minus tolerance.
(2) This tolerance might not apply in localized areas of shaped fittings wherever increased wall thickness is needed to fulfill the look needs of ASME B16.9.
(3) the within diameter and therefore the nominal wall thicknesses at ends area unit to be such by the buyer. (4) Unless otherwise such by the vendee, these tolerances apply to the nominal within diameter, that equals the distinction between the nominal outside diameter and double the nominal wall thickness.
½ to 4
0.03
0.06
5 to 8
0.06
0.12
10 to 12
0.09
0.19
14 to 16
0.09
0.25
18 to 24
0.12
0.38
26 to 30
0.19
0.38
32 to 42
0.19
0.50
44 to 48
0.18
0.75








Comments

Popular posts from this blog

Buy Long Radius Bends In India

Top 3 Best product 304l stainless steel sa 234 gr wpb sa 234 gr wpb You have never seen

Top 5 Stainless steel flanges manufacturer information in - Mesta Inc